Your Cart

Limited Time Only: FREE SHIPPING on all orders over $69.99! (U.S. only)

Arland’s Hood

There is something magical that happens when you wear a hood, it is like bringing a fairy tale to life! 

LOOM: 18″ All-n-One Loom

YARN: Approx 420 yds of worsted weight Peruvian wool blend. Knit Picks Wool of the Andes Tweed in Prussian Heather was used in sample. 110 yards/50 grams.

NOTIONS: Row counter, knitting tool, tapestry needle. ½” decorative button

GAUGE: 10 sts x 14 rows= 2 inches in stockinette

SIZE: Approx 17 inches in long x 10” wide.

ABBREVIATIONS

Approx=approximate

K=knit

P=purl

St(s)=stitch(es)


INSTRUCTIONS

Hood

(Make 2)

Cast on 86 sts, prepare to work a flat panel.

Row 1 (from right to left): k6, *p2, k6; rep from * to end of row.

Row 2: p1, *k4, p4; rep from * to last 5 sts, k4, p1.

Row 3: p2, *k2, p2; rep from * to end.

Row 4: k1, *p4, k4; rep from * to last 5 sts, p4, k1.

Row 5: k2, *p2, k6; rep from * to last 4 sts, p2, k2.

Row 6: k6, *p2, k6; rep from * to end.

Row 7: p1, *k4, p4; rep from * to last 5 sts, k4, p1.

Row 8: p2, *k2, p2; rep from * to end.

Row 9: k1, *p4, k4; rep from * to last 5 sts, p4, k1.

Row 10: k2, *p2, k6; rep from * to last 4 sts, p2, k2.

Repeat Rows 1-10 until panel measures approximately 7 inches from cast on edge. End on a Row 10 (Approximately 70 rows, 7 repeats of Rows 1-10).

Next 12 rows: *k2, p2; rep from * to end.

Next row: p to end.

Next 12 rows: *k2, p2; rep from * to end.

Bind off with basic bind off method.

 

 

 

 

 

 

 

 

 

 

 

 

 

Bottom Ribbed Hem

Cast on 106 sts, prepare to work a flat panel.

Row 1-10: *k2, p2; rep from * to last 2sts, k2.

Row 11:  k2, p2, bind off 2 sts, p2, *k2, p2; rep from * to last 2 sts, k2.

Row 12: k2, p2, cast on 2 sts, p2; *k2, p2; rep from * to last 2 sts, k2

Bind off with basic bind off method.

 

 

 

 

 

 

 

 

Assembly

Steam block the 2 hood pieces before assembly. Do not steam block the Bottom Ribbed Hem.

Mattress stitch the top of the two pieces, then down the back side of the hood.

Mattress stitch the Bottom Ribbed Hem to the bottom section of the hood.

Match the buttonhole to the button placement. Sew in a decorative button.

 

 

 

 

0 comments

  1. Can this be made in one piece? So no sewing parts

    1. Hi Gin, yes, you can. You will need a knitting loom that has twice the amount of pegs as called for in the pattern. You will still need to create the bottom piece separately though as that goes in the opposite direction of the hood.

  2. Can this be made as one piece.

    1. Yes. You will need a knitting loom that has twice the amount of pegs as called for in the pattern.

  3. Kathy Blosser

    Hi Isela, love this hood, and would love to make it. But l don’t have the all in one loom. Can it be made on any other loom?

    1. Kathy, you can make it on any other loom that is similar gauge to the All-n-One loom. You will need the same amount of pegs too.

  4. Can this be made into a hooded scarf? If so can it be done as a modular knit piece? All in one piece? No patterns for a hooded scarf for the loom??? I have looked and have been asked by many. This looks like it can be possible??

    1. Yes, any of the small gauge looms like the 18″ All-n-One Loom in single knit can be knit on the Flexee Loom Skinny.

Leave a Reply

Your email address will not be published. Required fields are marked *